Bicycle Research Product Frame Tools

| Slide Hammer | Cup Press | Chainwheel Straightener | Brake Boss Repair

**Headset Tools**

**( HT1; HT2; HT3 )**
click on image for a detailed view
Ream the inside and mill the end of the headtube all at once... also used as a press to fit bearings or cups into the head tube of the frame with a great deal of accuracy. Tool steel reamer and face cutter, lightweight alloy handle. Instructions on care and use are included. HT1 for 1" headsets, HT2 for 1 1/8", & HT3 for 1 1/4" mountain bike headsets. To Index

Fork Crown Race Mill

(FCH)

click on image for a detailed view

Used to accurately mill the fork crown/steer tube junction for fitting the bottom headset bearing race. FCH is a set of cutters with an anodized aluminum alloy holding body. Interchangeable cutting tools include pilots for steer tube sizes 1", 1 1/8" & 1 1/4".

Handle	FCH	- interchangeable -
Cutter	FCC - 1	26.4 mm for 1"
Cutter	FCC - 2	27.0 mm for 1" (JIS)
Cutter	FCC - 3	30.0 mm for 1 1/8"
Cutter	FCC - 4	33.0 mm for 1 1/4"

To Index

Frame Blocks

click on image for a detailed view

Originally designed to squeeze wrinkles out of frame tubes, these Frame Blocks are great for quickly clamping tubes in a vise or used in a frame jig... all kinds of uses for these blocks. Heat treated aluminum alloy, accurately bored to size.

(FB1) for 1"

(FB1.125) for 1 1/8"

(FB1.250) for 1 1/4"

To Index

**Alloy Crank Arm Thread Chaser**

**( TC -8 )**
click on image for a detailed view
Re-forms extractor and or dust cap threads that have been damaged by hitting rocks, or by cross threading. Guide shaft screws into spindle - male or female - to assure a proper start of the chaser. Use either the original crank bolt or nut with a washer to help push the thread chaser up against the damaged threads. To Index

Slide Hammer

( SH 1, SH 1.125, SH 1.250

click on image for a detailed view

Use to seat the fork crown bearing race onto the fork steer tube quickly and easily.

SH 1	For 1" Steerer Tubes
SH 1.125	For 1 - 1/8" Steerer Tubes
SH1.250	For 1 - 1/4" Steerer Tubes

To Index

**Cup Press**

**( CP )**
click on image for a detailed view
For installing bearings into American type bicycle frames as well as BMX and/or cruisers. Install one piece bottom bracket bearing cups and headset cups for frames with head tubes up to 5" long. Shorten a second cup press to 3" with a hack saw for quick installation of bottom bracket cups and/or BMX cartiridge bearings. To Index

**ChainWheel Straightening Tool**

**( LC )**
click on image for a detailed view
For bent chain rings and bent chainwheel sprockets. Helps to improve derailleur function. This handy tool means a quick reach between the rings to the bent section. One quick movement and the problem is corrected! To Index

Brake Boss Repair

( BM 8 and BM 9)

click on image for a detailed view

These tool steel cutters are used to repair damaged or oversize brake bosses on frames and forks. Also may be used to remove paint or flux from the brake boss. Includes a pilot screw to ensure that the cutter is properly aligned before the cut is started. The pilot screw stores in the end of the cutter to prevent loss.

BM 8	for 8mm cantilever brake bosses
BM 9	for 9mm U Brake bosses

To Index

Frame Tools
To Wheel Tools
To Accessories